收藏本站
Atmel LED Drivers-MSL1061/MSL1064
6-string PWM LED Driver with Digitally Compensated, 1.1MHz,
48V Boost Regulator, ±1.5% Current Balance, I 2 C Interface
V TRIP = V OVP
Boost Regulator Components
The boost regulator is internally compensated, includes
an internal high voltage power switch, and requires only
an inductor, rectifier, and bypass capacitors. The current-
mode boost regulator operates in either continuous
conduction mode (CCM) or discontinuous conduction
mode (DCM). In CCM, the inductor current does not fall
to zero when operating at full power, keeping inductor
ripple current low and switching noise at a minimum.
The boost regulator switching frequency is 1.1MHz set
by the 115k ? resistor R4 from OSC pin to GND (Figure
6). Select the inductor, rectifier diode, and output
capacitors per the following guidelines.
To minimize losses in the rectifier, choose one with fast
switching and low forward voltage drop. Ensure that the
rectifier can withstand a reverse voltage equal to the
regulator output voltage. The average forward current
is equal to the total LED string current (for example 6
strings x 30mA = 180mA), while the peak current is
equal to the inductor peak current (2A).
The boost output capacitor holds the voltage at the
output of the boost regulator while the internal power
switch is on and the rectifier is not conducting. Use
ceramic capacitors for small size and high ripple current
capacity, and derate them for operating voltage because
of the voltage coefficient of capacitance which decreases
the effective capacitance with increased operating
voltage. Use two parallel-connected 1μF 100V X7R
ceramic capacitors and a 10μH inductor with a 1.7A
peak current rating.
Atmel LED Drivers-MSL1061/MSL1064
Boost Supply Over-voltage Protection
(OVP) - R8 and R9
The OVP input sets the boost regulator’s output voltage
upper limit, and protects the boost regulator from an
open-circuit LED fault. Set the OVP voltage V TRIP by
resistors R8 and R9 (Figure 6):
( R 8 + R 9 )
R 9
where V OVP =1.28V, nominal.
17
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
MSL2041GU IC LED DRIVER 4 STRING
MSL2100BR IC LED DRIVER 8 STRING
MSL2160DQ IC LED DRIVER 16 STRING
MSL2162DQ IC LED DRIVER 16 STRING
MSL3082CS IC LED DRIVER 8 STRING
MSL3085BT IC LED DRIVER 8 STRING
MSL3162BT IC LED DRIVER 16 STRING
MSL3164BT IC LED DRIVER 16 STRING
相关代理商/技术参数
MSL1061AV-R 功能描述:LED照明驱动器 6Str LED Dvr Dgtl 1.1MHz 48V r 1.5% RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MSL1064 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:6-string PWM LED Driver with Digitally Compensated, 1.1MHz, 48V Boost Regulator, ±1.5% Current Balance, I2C Interface
MSL1064AW 功能描述:LED照明驱动器 6Str PWM LED Dvr Dgt 1.1MHz 48V 1.5% I RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MSL1064AW-R 功能描述:LED照明驱动器 6Str PWM LED Dvr Dgt 1.1MHz 48V1.5% I RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MSL1064-TC 功能描述:LED照明驱动器 6Str PWM LED Dvr Dgt 1.1MHz 48V+/-1.5% I RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MSL106E 制造商:TE Connectivity 功能描述:
MSL-1-1/2 制造商:Cooper Bussmann 功能描述:
MSL-1-1/4 制造商:Cooper Bussmann 功能描述: